“ラックスマン”社-“スピーカーセレクター”-“AS-5Ⅲ”(AS-5III)-“スピーカーを切替える装置のレビュー!!

今回は私が長年愛用している日本の音響機器の老舗メーカーである
ラックスマン株式会社 (LUXMAN CORPORATION)の
スピーカーセレクターである【AS-5Ⅲ】を紹介します。

この機材の凄いところは
30年くらい形も中身も変わってない事です。
そういう猛烈に強いポリシーのある質実剛健な企業に私は"弱い"です。

この機材の最大のポイントは"ディスクトリート配線"であるという点です。

"ディスクリート"ってなんだよ?ってなる方もおられるかもしれません。

この用語は半導体などで使用される単語と記憶していますが,
簡単にいえば"ディスクリートとはある回路において
ひとつひとつ異なる部品が使われている"という意味だと思っております。

今回,私が撮影した本体内部の画像をRandomですが複数掲載しましょう。

押しボタンは4つ。軽快です。
押すと"押した"と分かる位に軽快に音が出ます。
(音源ソースの音ではなくてあくまでスイッチの音です)。

私の様な人間にとって分かりやすいスイッチは"武器"です。
押したのか押してないのか分からないようなスイッチは嫌いです。

各ボタンを押すと各配線されたスピーカーに瞬時に出力されます。

スイッチした際,ノイズは皆無です。
ボタンを押しても,いかなる時も
無駄なノイズは一切出ません。

音やせ??
あるかないか??それは重要ですが・・
机上の空論ではあるのかもしれませんが,
少なくともこのAS5-Ⅲに関して述べれば私の聴感上では全くもって皆無です。

内部を見て,素晴らしい職人技の半田付けを見る限り,惚れ惚れとしますが,
気になるのは内部線の細さです。よくこの細さで,音痩せがしないものだと
個人的には感じています。

ただ,私の聴感というのは
例えば"OCC"と"OFC"のケーブル素材が変わってもその変化には気づきません。
それだけの聴力と感性しかないとい事で勘弁して頂けると幸いです。

音楽に関しては私は机上の空論を全て一切信用しません。

余談ですが,究極のシステムを構築するならば別室に設置した水冷却装置の
導入が不可欠だと思います。全ての有線は極めて純度の高い銅線
を使用しその有線を中に通すホースに流動する冷却水を絶えず流し温度を下げる。
全ては"電子"の動きを活発にする為です。
それが私なりの有線使用での究極的な使用方法ですがもし,
それを試行するとなればシステムに依っては
音響ケーブルのセッティングだけで数千万から
億単位のコストが必要となるのではないでしょうか?

話が逸れました。本体の記事に戻します。

Dのみがヘッドホンでモニタリングが可能です。
音量は調節出来ません。
至って素直な自然な音が流れてきます。

おもしろいのは,
このスピーカーセレクターを
逆に分岐配置することも可能なのです。以下の画像の様に,
アンプが一杯あって(殆ど店以外あり得ませんが・・)一個のスピーカーで鳴らす場合など。
今は発想が貧困なので咄嗟に思いつきませんが,
アイディア次第でおもしろいシステムを構築する事も出来そうです。

この機材は100点どころか,150点です。
価格に見合っていません。何度か自作でスピーカーセレクターを制作しようと
思った事があって部品の見積もりとかしてみた事があるのですが,駄目でした。
凄い金額になってしまうのですw。

使用していて,
気に入らない事も少しは述べないとレビューにはなりませんね。

何もかもおまえの全部が"好きだ"なんて恋愛でも相手にまず信用されませんよねw。

機材のレビューだったら尚更です。
気に入らない所もあって"好き"こそが
それらを完全に凌駕している,

長年愛着のある機材もまた
人間関係に近接した要素があるのかもしれません。

駄目な部分を述べます。
このAS5-Ⅲは"軽量"な事です。
スペック上では750g。

正直あと2千円アップしても良いから内部に"鉛"でも溶接して入れて欲しい。

オーナーの外部接続された導線(有線)はそれなりの重量があります。

据え置きしているとそのケーブルの重さに耐えられずに本体が浮いてきてしまう。
この課題は解決した方がいいと思います。

ただこの問題も簡単に使用者側で解決出来てしまいます。
機材の底をそれなりに加工(接着)
すれば良いことです。

両面テープを使ったり,自己融着テープの使用,
マジックテープなどの使用等。機材をロックする手段は多くあります。

次は,多くの有志の方々の記事を拝読しても同様の意見となりますが,
スピーカーコードの穴径が小さすぎます。

この機材を使用するユーザー層を考慮すれば,かなりのオーディオマニアか,
それなりに音響機器に精通した者,つまり一般のひと向けではありません。
スピーカーケーブルも相当太いものが挿入されるという事をまずは考慮して欲しい。

私の場合は,端子を使用せず,
見た目を重視(商用スタジオ経営者ではない)しないので,
直接,バラ線を捻って挿入してますが,
太いケーブルはさすがに全て"咥えて"はくれません。

↑近年は一切高級スピーカーを購入していません。

一瞬ドリルで穴を拡げてやろうか?と思った事も何度かあったのですが,
止めておきましたw。

外観はとても地味で,全く私好みではありません。

それでも,このラックスマン社のAS5-Ⅲに触れる=タッチする事を
実はいつもいつも楽しみにしているみたいです。

優れた機材というのはかくこういうものであるという
逸材だと思っています。

いつも私のサイトは長文の記事ばかりですが,
短く〆させて頂きます。

何も,もうこれ以上言うことのない程の逸品です。
【編集後記】
そういえばイタリア製のSICAのスピーカーのレビューがまだアップしていませんでした。
既に8月にインサートし良い状態ですので,是非別の記事でお話がしたいです。
それでは!


It introduces 【 AS-5 Ⅲ 】 that is the speaker selector of Laksman Ltd. (LUXMAN CORPORATION)
that is a long-established manufacturer of the acoustical instrument of Japan that I am patronizing for years this time.
The point where this machine parts is terrible is a thing that shape and contents do not change by about 30 years.

I am "It is weak. " in such a sturdy simple enterprise where a strong policy exists severely
It is a point "Disk treat wiring" the point of the the greatest of this machine parts.
"Discrete" might also have seeming as what.

It thinks this term to be a meaning "Different one by one parts are used with discrete in the circuit that is" if it says easily though it is memorized as the word used with the semiconductor etc.
This time, two or more images in the main body of which I took a picture are published.
The push-button is four.
It is light.
The sound is lightly emitted to the place that understands, "Pushed" when pushing.
(It is not a sound of the sound source source but it is a sound of the switch to the end. )
A comprehensible switch for my man is "Arms. "
I hate switch not to understand whether to have pushed or not to push.
When each button is pushed, it is instantaneously output to the speaker each wired for.
When the switch is done, the noise is none at all.
A useless at any time noise doesn't occur even if the button is pushed.
Sound becomeing thin.
Do not you be or exist? Though it is important ‥ It completely has on my audibility if this AS5 - Ⅲ is at least described and it is none at all though it might be a desk theory.
It is thin though it is assumed love love as long as the inside is seen, and soldering wonderful craftsmanship is seen that it is anxious in an internal line.
It is personally felt well that it is thin of this, and what the sound becomeing thin doesn't do.
However, even if the cable material of "OCC" and "OFC" changes for instance, my audibility doesn't notice the change.

It would be greatly appreciated when it is possible to pardon it by the question thing that has only hearing and the sensibility only of it.
I do not trust all desk theories for music at all.
I think that the introduction of the water cooling device set up in the another room is indispensable if an ultimate system is constructed though it is a bytalk.
All cable lowers the cooling water that flows to the hose that passes the cable through the inside by using the copper wire with extremely high purity and the temperature of the sink is always lowered.
The reason for all is that the movement of "Electron" is made active.
The cost of hundred million unit might be needed from several ten million only in the setting of the sound cable if depending on the system if becoming it if it is tried though it is ultimate usage in the use of the cable of my own way.
The talk is returned to the main body.
Only D can be monitored with the headphone.
The volume cannot be adjusted.
A natural obedient fairly sound flows.
Interesting..this..speaker..selector..opposite..divergence..dispose..possible.


There is fully an amplifier like the following images (Though it can be hardly excluding the shop) and it sounds it with one speaker.
Pshaw because the conception is poor, I think that I can do an interesting system depending on the idea in though it doesn't hit on.

This machine parts is 150 points to say nothing of 100 points.
It doesn't correspond to the price.
It was useless though the speaker selector was going to be produced with making by oneself several times before and parts had been estimated.
It is w in a terrible amount of money to have ..becoming...
If the thing doesn't like because it uses it is not described a little, it doesn't become a review.

All love is really "It is favorite" w not trusted by the other party ..all of you...
It is still natural of machine parts when reviewing.
There is a place doesn't like either and only "Favor" surpasses them completely.
For years, machine parts with the attachment might also have the close element in the interpersonal relationship.

↑ Recently, a high-level speaker is not bought at all.

A useless part is described.
This AS5 - Ⅲ is "Lightness. "
750g on specs.
Because you may improve for 2,000 yen after honesty, I ..inside.. want you to weld and to put it as for "Lead".
The lead (cable) with which the external of the owner is connected has moderate weight.
The main body it is not possible to endure floats on the weight of the cable when leaving it untouched.
I think that you should solve this problem.
However, this problem can be easily solved on the user side.
As such, it only has to process the bottom of machine parts (bond).
The double-faced tape is used, and the self-bonding tape is used.
Use etc. such as Velcro.
There are a lot of means to lock machine parts.
The hole-diameter of the speaker code is too small though the following become similar opinions even if a lot of articles of volunteers are read.
If the group of users that uses this machine parts is considered, for a general person who is well versed in the acoustical instrument as such whether it is a considerable audiophile ,in a word, person.
I want you to consider the thing that the thick line is considerably inserted as for the speaker cable first of all.
The thick cable doesn't give "Hold it in one's mouth" indeed all though the rose line is twisted directly and it inserts it for me because externals are not valued without using the terminal (It is not a studio manager).

Stopped w though there were several-time things thought whether I will expand the hole by the drill at the moment, too.

Externals are very sober, and not favors at all.
Still, it seems to look forward to = thing that it touches AS5 - Ⅲ of this Laksman Co. to touch actually always always.
It is thought that it is a man of exceptional talent that excellent machine parts is such the one thus.
My site is always short and 〆 though only the article on the long sentence.
Anything is an excellent article so that it is not likely to say any further.

【 Editor's note 】
Incidently, the review of the speaker of SICA made in Italy had not improved yet.
I want to insert in August and to be already good, and to talk by all means by another article.
See you later!

コメントする

メールアドレスが公開されることはありません。 が付いている欄は必須項目です